bsp_config.c修改完毕

source/app/main.c

@@ -109,14 +109,17 @@ void L0_main_init(void)
 //===============================================
 void main(void)
 {
+#if 0
 	L0_board_config();
-	while(0);
+	while(1)
 	{
 		LED0 = LED0_ON;
 		delayInMs(500);
 		LED0 = LED0_OFF;
 		delayInMs(500);
 	}
+#endif
+
 	//初始化
 	L0_main_init();
 	//验证加密信息

source/bsp/bsp_config.c

@@ -24,6 +24,18 @@
 
 void L0_board_config(void)
 {
+	//LED
+	D_stdIO_P0_ALL();
+	D_stdIO_P1_ALL();
+	D_stdIO_P2_ALL();
+	D_stdIO_P3_ALL();
+	D_stdIO_P4_ALL();
+	//IO
+	BLED0 = BLED1 = BLED2 = BLED3 = BLED4 = BLED5 = BLED6 = BLED0_OFF;
+	BLED7 = BLED8 = BLED9 = BLED10 = BLED11 = BLED12 = BLED13 = BLED0_OFF;
+	LED0 = LED0_ON;
+
+	//uart0
 #if (PIN_UART0_Rxd_30_Txd_31 == D_PIN_UART0)
 	BITN_0(P_SW1 ,BITN7);//
 	BITN_0(P_SW1 ,BITN6);// rxd p3.0 txd p3.1
@@ -42,31 +54,37 @@ void L0_board_config(void)
 #endif
 
 	//uart2
+#if (PIN_UART2_Rxd_10_Txd_11 == D_PIN_UART2)
 	BITN_0(P_SW2 ,BITN0);// rxd2 p1.0 txd2 p1.1	
-	//BITN_1(P_SW2 ,BITN0);// rxd2 p4.0 txd2 p4.2
-
-	//uart3
-	//P_SW2 = 0x02; // RXD3_2/P5.0, TXD3_2/P5.1
+#elif (PIN_UART2_Rxd_46_Txd_47 == D_PIN_UART2)
+	BITN_1(P_SW2 ,BITN0);// rxd2 p4.06 txd2 p4.7
+#else
+	BITN_0(P_SW2 ,BITN0);// rxd2 p1.0 txd2 p1.1	
+#endif
 
 	//uart4
-	//BITN_1(P_SW2 ,BITN2);// rxd4 p5.2 txd4 p5.3	
-	//BITN_0(P_SW2 ,BITN2);// rxd4 p0.2 txd4 p0.3
-
-	//485 RE/DE 配置推完输出 P55
-	BITN_0(P5M1,BITN5);BITN_1(P5M0,BITN5);
+#if (PIN_UART3_Rxd_00_Txd_01 == D_PIN_UART3)
+	BITN_0(P_SW2 ,BITN1);// rxd2 p1.0 txd2 p1.1	
+#elif (PIN_UART3_Rxd_50_Txd_51 == D_PIN_UART3)
+	BITN_1(P_SW2 ,BITN1);// rxd2 p4.06 txd2 p4.7
+#else
+	BITN_0(P_SW2 ,BITN1);// rxd2 p1.0 txd2 p1.1	
+#endif
 
-	//LED
-	D_stdIO_P0_ALL();
-	D_stdIO_P1_ALL();
-	D_stdIO_P2_ALL();
-	D_stdIO_P3_ALL();
-	D_stdIO_P4_ALL();
+	//uart4
+#if (PIN_UART4_Rxd_02_Txd_03 == D_PIN_UART4)
+	BITN_0(P_SW2 ,BITN2);// rxd2 p1.0 txd2 p1.1	
+#elif (PIN_UART4_Rxd_52_Txd_53 == D_PIN_UART4)
+	BITN_1(P_SW2 ,BITN2);// rxd2 p4.06 txd2 p4.7
+#else
+	BITN_0(P_SW2 ,BITN2);// rxd2 p1.0 txd2 p1.1
+#endif
 
-	//IO
-	BLED0 = BLED1 = BLED2 = BLED3 = BLED4 = BLED5 = BLED6 = BLED0_OFF;
-	BLED7 = BLED8 = BLED9 = BLED10 = BLED11 = BLED12 = BLED13 = BLED0_OFF;
-	LED0 = LED0_ON;
+	//485 RE/DE 配置推完输出 P00,P01
+	D_HighI_P0(BITN0);
+	D_HighI_P0(BITN1);
 
+	//WDT
 	#if (TYPE_WDT_ENABLE == D_WDT_STATUS)
 	WDT_CONTR = 0x27;     //使能看门狗,22M时钟下溢出时间约为5s，请注意添加喂狗程序
 	#else