#ifndef __STC_stc8a8k_H_
#define __STC_stc8a8k_H_
// STC_stc8a8k.h
#include<intrins.h>

/////////////////////////////////////////////////
//注意: STC15W4K32S4系列的芯片,上电后所有与PWM相关的IO口均为
//      高阻态,需将这些口设置为准双向口或强推挽模式方可正常使用
//相关IO: P0.6/P0.7/P1.6/P1.7/P2.1/P2.2
//        P2.3/P2.7/P3.7/P4.2/P4.4/P4.5
/////////////////////////////////////////////////

/////////////////////////////////////////////////

//包含本头文件后,不用另外再包含"REG51.H"

//内核特殊功能寄存器        // 复位值   描述
sfr ACC         =   0xE0;   //0000,0000 累加器Accumulator
sfr B           =   0xF0;   //0000,0000 B寄存器
sfr PSW         =   0xD0;   //0000,0000 程序状态字
sbit CY         =   PSW^7;
sbit AC         =   PSW^6;
sbit F0         =   PSW^5;
sbit RS1        =   PSW^4;
sbit RS0        =   PSW^3;
sbit OV         =   PSW^2;
sbit P          =   PSW^0;
sfr SP          =   0x81;   //0000,0111 堆栈指针
sfr DPL         =   0x82;   //0000,0000 数据指针低字节
sfr DPH         =   0x83;   //0000,0000 数据指针高字节

//I/O 口特殊功能寄存器
sfr P0          =   0x80;   //1111,1111 端口0
sbit P00        =   P0^0;
sbit P01        =   P0^1;
sbit P02        =   P0^2;
sbit P03        =   P0^3;
sbit P04        =   P0^4;
sbit P05        =   P0^5;
sbit P06        =   P0^6;
sbit P07        =   P0^7;
sfr P1          =   0x90;   //1111,1111 端口1
sbit P10        =   P1^0;
sbit P11        =   P1^1;
sbit P12        =   P1^2;
sbit P13        =   P1^3;
sbit P14        =   P1^4;
sbit P15        =   P1^5;
sbit P16        =   P1^6;
sbit P17        =   P1^7;
sfr P2          =   0xA0;   //1111,1111 端口2
sbit P20        =   P2^0;
sbit P21        =   P2^1;
sbit P22        =   P2^2;
sbit P23        =   P2^3;
sbit P24        =   P2^4;
sbit P25        =   P2^5;
sbit P26        =   P2^6;
sbit P27        =   P2^7;
sfr P3          =   0xB0;   //1111,1111 端口3
sbit P30        =   P3^0;
sbit P31        =   P3^1;
sbit P32        =   P3^2;
sbit P33        =   P3^3;
sbit P34        =   P3^4;
sbit P35        =   P3^5;
sbit P36        =   P3^6;
sbit P37        =   P3^7;
sfr P4          =   0xC0;   //1111,1111 端口4
sbit P40        =   P4^0;
sbit P41        =   P4^1;
sbit P42        =   P4^2;
sbit P43        =   P4^3;
sbit P44        =   P4^4;
sbit P45        =   P4^5;
sbit P46        =   P4^6;
sbit P47        =   P4^7;
sfr P5          =   0xC8;   //xxxx,1111 端口5
sbit P50        =   P5^0;
sbit P51        =   P5^1;
sbit P52        =   P5^2;
sbit P53        =   P5^3;
sbit P54        =   P5^4;
sbit P55        =   P5^5;
sbit P56        =   P5^6;
sbit P57        =   P5^7;
sfr P6          =   0xE8;   //0000,0000 端口6
sbit P60        =   P6^0;
sbit P61        =   P6^1;
sbit P62        =   P6^2;
sbit P63        =   P6^3;
sbit P64        =   P6^4;
sbit P65        =   P6^5;
sbit P66        =   P6^6;
sbit P67        =   P6^7;
sfr P7          =   0xF8;   //0000,0000 端口7
sbit P70        =   P7^0;
sbit P71        =   P7^1;
sbit P72        =   P7^2;
sbit P73        =   P7^3;
sbit P74        =   P7^4;
sbit P75        =   P7^5;
sbit P76        =   P7^6;
sbit P77        =   P7^7;


///00 准双向口 灌电流20mA 拉电流270-150uS 
///01 推挽输出 20mA 加限流 
///10  高阻
///11 开漏 open-Drain 内部上拉电阻断开 开漏模式既可以度外部状态也可以对外输出高低电平


sfr P0M0        =   0x94;   //0000,0000 端口0模式寄存器0
sfr P0M1        =   0x93;   //0000,0000 端口0模式寄存器1
sfr P1M0        =   0x92;   //0000,0000 端口1模式寄存器0
sfr P1M1        =   0x91;   //0000,0000 端口1模式寄存器1
sfr P2M0        =   0x96;   //0000,0000 端口2模式寄存器0
sfr P2M1        =   0x95;   //0000,0000 端口2模式寄存器1
sfr P3M0        =   0xB2;   //0000,0000 端口3模式寄存器0
sfr P3M1        =   0xB1;   //0000,0000 端口3模式寄存器1
sfr P4M0        =   0xB4;   //0000,0000 端口4模式寄存器0
sfr P4M1        =   0xB3;   //0000,0000 端口4模式寄存器1
sfr P5M0        =   0xCA;   //0000,0000 端口5模式寄存器0
sfr P5M1        =   0xC9;   //0000,0000 端口5模式寄存器1
sfr P6M0        =   0xCC;   //0000,0000 端口6模式寄存器0
sfr P6M1        =   0xCB;   //0000,0000 端口6模式寄存器1
sfr P7M0        =   0xE2;   //0000,0000 端口7模式寄存器0
sfr P7M1        =   0xE1;   //0000,0000 端口7模式寄存器1

//系统管理特殊功能寄存器
sfr PCON        =   0x87;   //0001,0000 电源控制寄存器
sfr AUXR        =   0x8E;   //0000,0000 辅助寄存器

#define  TOx12	BITN7		
#define  T1x12	BITN6		 
#define  UART_M0x6	BITN5	//串口1模式0速度 =0 12倍 = 1 两倍
#define  T2R	BITN4		//定时器2 运行 =1
#define  T2_C	BITN3	//定时器/计数器选择
#define  T2x12	BITN2
#define  EXTRAM 	BITN1
#define  S1ST2 	BITN0			//串口1选择定时器1 =0  选择定时器2 =1




sfr AUXR1       =   0xA2;   //0000,0000 辅助寄存器1
sfr P_SW1       =   0xA2;   //0000,0000 外设端口切换寄存器1
sfr CLK_DIV     =   0x97;   //0000,0000 时钟分频控制寄存器
sfr BUS_SPEED   =   0xA1;   //xx10,x011 总线速度控制寄存器
sfr P1ASF       =   0x9D;   //0000,0000 端口1模拟功能配置寄存器
//-----------------------------------------------------------------
sfr P_SW2       =   0xBA;   //0xxx,x000 外设端口切换寄存器
#define EAXFR	BITN7
#define I2C_S1	BITN5
#define I2C_S2	BITN4
#define CMPO_S	BITN3
#define S4_S	BITN2
#define S3_S	BITN1
#define S2_S	BITN0

//-----------------------------------------------------------------

//中断特殊功能寄存器
sfr IE          =   0xA8;   //0000,0000 中断控制寄存器
sbit EA         =   IE^7;
sbit ELVD       =   IE^6;
sbit EADC       =   IE^5;
sbit ES         =   IE^4;
sbit ET1        =   IE^3;
sbit EX1        =   IE^2;
sbit ET0        =   IE^1;
sbit EX0        =   IE^0;
sfr IP          =   0xB8;   //0000,0000 中断优先级寄存器
sbit PPCA       =   IP^7;
sbit PLVD       =   IP^6;
sbit PADC       =   IP^5;
sbit PS         =   IP^4;
sbit PT1        =   IP^3;
sbit PX1        =   IP^2;
sbit PT0        =   IP^1;
sbit PX0        =   IP^0;
sfr IE2         =   0xAF;   //0000,0000 中断控制寄存器2
/// 不可位寻址
#define  ET4	BITN6
#define  ET3	BITN5
#define  ES4	BITN4
#define  ES3	BITN3
#define  ET2	BITN2
#define  ESPI 	BITN1
#define  ES2 	BITN0

sfr IP2         =   0xB5;   //xxxx,xx00 中断优先级寄存器2
sfr INT_CLKO    =   0x8F;   //0000,0000 外部中断与时钟输出控制寄存器

//定时器特殊功能寄存器
sfr TCON        =   0x88;   //0000,0000 T0/T1控制寄存器
sbit TF1        =   TCON^7;
sbit TR1        =   TCON^6;
sbit TF0        =   TCON^5;
sbit TR0        =   TCON^4;
sbit IE1        =   TCON^3;
sbit IT1        =   TCON^2;
sbit IE0        =   TCON^1;
sbit IT0        =   TCON^0;
sfr TMOD        =   0x89;   //0000,0000 T0/T1模式寄存器
sfr TL0         =   0x8A;   //0000,0000 T0低字节
sfr TL1         =   0x8B;   //0000,0000 T1低字节
sfr TH0         =   0x8C;   //0000,0000 T0高字节
sfr TH1         =   0x8D;   //0000,0000 T1高字节
sfr T4T3M       =   0xD1;   //0000,0000 T3/T4模式寄存器
sfr T3T4M       =   0xD1;   //0000,0000 T3/T4模式寄存器
sfr T4H         =   0xD2;   //0000,0000 T4高字节
sfr T4L         =   0xD3;   //0000,0000 T4低字节
sfr T3H         =   0xD4;   //0000,0000 T3高字节
sfr T3L         =   0xD5;   //0000,0000 T3低字节
sfr T2H         =   0xD6;   //0000,0000 T2高字节
sfr T2L         =   0xD7;   //0000,0000 T2低字节
sfr WKTCL       =   0xAA;   //0000,0000 掉电唤醒定时器低字节
sfr WKTCH       =   0xAB;   //0000,0000 掉电唤醒定时器高字节
sfr WDT_CONTR   =   0xC1;   //0000,0000 看门狗控制寄存器

//串行口特殊功能寄存器
sfr SCON        =   0x98;   //0000,0000 串口1控制寄存器
sbit SM0        =   SCON^7;
sbit SM1        =   SCON^6;
sbit SM2        =   SCON^5;
sbit REN        =   SCON^4;
sbit TB8        =   SCON^3;
sbit RB8        =   SCON^2;
sbit TI         =   SCON^1;
sbit RI         =   SCON^0;
//sfr SBUF        =   0x99;   //xxxx,xxxx 串口1数据寄存器
//sfr S2CON       =   0x9A;   //0000,0000 串口2控制寄存器
//sfr S2BUF       =   0x9B;   //xxxx,xxxx 串口2数据寄存器
//sfr SADDR       =   0xA9;   //0000,0000 从机地址寄存器
//sfr SADEN       =   0xB9;   //0000,0000 从机地址屏蔽寄存器

sfr SBUF = 0x99; //Serial Data Buffer    
sfr SBUF0 = 0x99; //Serial Data Buffer                                                     xxxx,xxxx
sfr SADEN = 0xB9; //Slave Address Mask                                                    0000,0000
sfr SADDR = 0xA9; //Slave Address                                                         0000,0000
//-----------------------------------
//                                7      6      5      4      3      2     1     0        Reset Value
sfr S2CON = 0x9A; //S2 Control  S2SM0  S2SM1  S2SM2  S2REN  S2TB8  S2RB8  S2TI  S2RI      00000000B
#define  S2SM0	BITN7
#define  S2ST4	BITN6
#define  S2SM2	BITN5
#define  S2REN	BITN4
#define  S2TB8	BITN3
#define  S2RB8	BITN2
#define  S2TI 	BITN1
#define  S2RI 	BITN0

sfr S2BUF = 0x9B; //S2 Serial Buffer                                                      xxxx,xxxx
//sfr BRT = 0x9C; //S2 Baud-Rate Timer                                                    0000,0000

//---------------------------------------------------------------
sfr S3CON       =   0xAC;   //0000,0000 串口3控制寄存器
#define  S3SM0	BITN7
#define  S3ST4	BITN6
#define  S3SM2	BITN5
#define  S3REN	BITN4
#define  S3TB8	BITN3
#define  S3RB8	BITN2
#define  S3TI 	BITN1
#define  S3RI 	BITN0

sfr S3BUF       =   0xAD;   //xxxx,xxxx 串口3数据寄存器
//---------------------------------------------------------------
sfr S4CON       =   0x84;   //0000,0000 串口4控制寄存器
#define  S4SM0	BITN7
#define  S4ST4	BITN6
#define  S4SM2	BITN5
#define  S4REN	BITN4
#define  S4TB8	BITN3
#define  S4RB8	BITN2
#define  S4TI 	BITN1
#define  S4RI 	BITN0

sfr S4BUF       =   0x85;   //xxxx,xxxx 串口4数据寄存器

//ADC 特殊功能寄存器
sfr ADC_CONTR   =   0xBC;   //0000,0000 A/D转换控制寄存器
sfr ADC_RES     =   0xBD;   //0000,0000 A/D转换结果高8位
sfr ADC_RESL    =   0xBE;   //0000,0000 A/D转换结果低2位

//SPI 特殊功能寄存器
sfr SPSTAT      =   0xCD;   //00xx,xxxx SPI状态寄存器
sfr SPCTL       =   0xCE;   //0000,0100 SPI控制寄存器
sfr SPDAT       =   0xCF;   //0000,0000 SPI数据寄存器

//IAP/ISP 特殊功能寄存器
sfr IAP_DATA    =   0xC2;   //0000,0000 EEPROM数据寄存器
sfr IAP_ADDRH   =   0xC3;   //0000,0000 EEPROM地址高字节
sfr IAP_ADDRL   =   0xC4;   //0000,0000 EEPROM地址第字节
sfr IAP_CMD     =   0xC5;   //xxxx,xx00 EEPROM命令寄存器
sfr IAP_TRIG    =   0xC6;   //0000,0000 EEPRPM命令触发寄存器
sfr IAP_CONTR   =   0xC7;   //0000,x000 EEPROM控制寄存器

//PCA/PWM 特殊功能寄存器
sfr CCON        =   0xD8;   //00xx,xx00 PCA控制寄存器
sbit CF         =   CCON^7;
sbit CR         =   CCON^6;
sbit CCF2       =   CCON^2;
sbit CCF1       =   CCON^1;
sbit CCF0       =   CCON^0;
sfr CMOD        =   0xD9;   //0xxx,x000 PCA 工作模式寄存器
sfr CL          =   0xE9;   //0000,0000 PCA计数器低字节
sfr CH          =   0xF9;   //0000,0000 PCA计数器高字节
sfr CCAPM0      =   0xDA;   //0000,0000 PCA模块0的PWM寄存器
sfr CCAPM1      =   0xDB;   //0000,0000 PCA模块1的PWM寄存器
sfr CCAPM2      =   0xDC;   //0000,0000 PCA模块2的PWM 寄存器
sfr CCAP0L      =   0xEA;   //0000,0000 PCA模块0的捕捉/比较寄存器低字节
sfr CCAP1L      =   0xEB;   //0000,0000 PCA模块1的捕捉/比较寄存器低字节
sfr CCAP2L      =   0xEC;   //0000,0000 PCA模块2的捕捉/比较寄存器低字节
sfr PCA_PWM0    =   0xF2;   //xxxx,xx00 PCA模块0的PWM寄存器
sfr PCA_PWM1    =   0xF3;   //xxxx,xx00 PCA模块1的PWM寄存器
sfr PCA_PWM2    =   0xF4;   //xxxx,xx00 PCA模块1的PWM寄存器
sfr CCAP0H      =   0xFA;   //0000,0000 PCA模块0的捕捉/比较寄存器高字节
sfr CCAP1H      =   0xFB;   //0000,0000 PCA模块1的捕捉/比较寄存器高字节
sfr CCAP2H      =   0xFC;   //0000,0000 PCA模块2的捕捉/比较寄存器高字节

//比较器特殊功能寄存器
sfr CMPCR1      =   0xE6;   //0000,0000 比较器控制寄存器1
sfr CMPCR2      =   0xE7;   //0000,0000 比较器控制寄存器2


//sfr     P_SW2       =   0xba;
sfr     PWMCFG      =   0xf1;
sfr     PWMIF       =   0xf6;
sfr     PWMFDCR     =   0xf7;
sfr     PWMCR       =   0xfe;

#define PWMC            (*(unsigned int volatile xdata *)0xfff0)
#define PWMCKS          (*(unsigned char volatile xdata *)0xfff2)
#define TADCP           (*(unsigned int volatile xdata *)0xfff3)
#define PWM0T1          (*(unsigned int volatile xdata *)0xff00)
#define PWM0T2          (*(unsigned int volatile xdata *)0xff02)
#define PWM0CR          (*(unsigned char volatile xdata *)0xff04)
#define PWM0HLD         (*(unsigned char volatile xdata *)0xff05)
#define PWM1T1          (*(unsigned int volatile xdata *)0xff10)
#define PWM1T2          (*(unsigned int volatile xdata *)0xff12)
#define PWM1CR          (*(unsigned char volatile xdata *)0xff14)
#define PWM1HLD         (*(unsigned char volatile xdata *)0xff15)
#define PWM2T1          (*(unsigned int volatile xdata *)0xff20)
#define PWM2T2          (*(unsigned int volatile xdata *)0xff22)
#define PWM2CR          (*(unsigned char volatile xdata *)0xff24)
#define PWM2HLD         (*(unsigned char volatile xdata *)0xff25)
#define PWM3T1          (*(unsigned int volatile xdata *)0xff30)
#define PWM3T2          (*(unsigned int volatile xdata *)0xff32)
#define PWM3CR          (*(unsigned char volatile xdata *)0xff34)
#define PWM3HLD         (*(unsigned char volatile xdata *)0xff35)
#define PWM4T1          (*(unsigned int volatile xdata *)0xff40)
#define PWM4T2          (*(unsigned int volatile xdata *)0xff42)
#define PWM4CR          (*(unsigned char volatile xdata *)0xff44)
#define PWM4HLD         (*(unsigned char volatile xdata *)0xff45)
#define PWM5T1          (*(unsigned int volatile xdata *)0xff50)
#define PWM5T2          (*(unsigned int volatile xdata *)0xff52)
#define PWM5CR          (*(unsigned char volatile xdata *)0xff54)
#define PWM5HLD         (*(unsigned char volatile xdata *)0xff55)
#define PWM6T1          (*(unsigned int volatile xdata *)0xff60)
#define PWM6T2          (*(unsigned int volatile xdata *)0xff62)
#define PWM6CR          (*(unsigned char volatile xdata *)0xff64)
#define PWM6HLD         (*(unsigned char volatile xdata *)0xff65)
#define PWM7T1          (*(unsigned int volatile xdata *)0xff70)
#define PWM7T2          (*(unsigned int volatile xdata *)0xff72)
#define PWM7CR          (*(unsigned char volatile xdata *)0xff74)
#define PWM7HLD         (*(unsigned char volatile xdata *)0xff75)


#define CKSEL			(*(unsigned char volatile xdata *)0xfE00)//108@ST8.PDF
#define MCLKODIV		BIT4
#define MCLKO_S			BITN3
#define MCLKSEL			BIT0

#define CLKDIV			(*(unsigned char volatile xdata *)0xfE01)//108@ST8.PDF
#define IRC24MCR		(*(unsigned char volatile xdata *)0xfE02)//108@ST8.PDF
#define XOSCCR			(*(unsigned char volatile xdata *)0xfE03)//108@ST8.PDF
#define IRC32KCR		(*(unsigned char volatile xdata *)0xfE04)//108@ST8.PDF



/////////////////////////////////////////////////



/*  P3  */
sbit RD   = 0xB7;
sbit WR   = 0xB6;
sbit T1   = 0xB5;
sbit T0   = 0xB4;
sbit INT1 = 0xB3;
sbit INT0 = 0xB2;
sbit TXD  = 0xB1;
sbit RXD  = 0xB0;




#if 0
/// >>>>> add by cc


//sbit P34=P3^4; //定义SDA数据线
//sbit P35=P3^5; //定义SCL时钟线
#define mBIT_1(X,N)	X|= (1<<N)
#define mBIT_0(X,N)	X&=~(1<<N)
#define mBIT_G(X,N)	(X&(1<<N))
/// add by cc 20181118
#define D_IO_normal_P0(n);	mBIT_0(P0M1,n);mBIT_0(P0M0,n); 
#define D_IO_normal_P1(n);	mBIT_0(P1M1,n);mBIT_0(P1M0,n); 
#define D_IO_normal_P2(n);	mBIT_0(P2M1,n);mBIT_0(P2M0,n); 
#define D_IO_normal_P3(n);	mBIT_0(P3M1,n);mBIT_0(P3M0,n);     

#define D_IO_HighOut_P0(n);	mBIT_0(P0M1,n);mBIT_1(P0M0,n); 
#define D_IO_HighOut_P1(n);	mBIT_0(P1M1,n);mBIT_1(P1M0,n); 
#define D_IO_HighOut_P2(n);	mBIT_0(P2M1,n);mBIT_1(P2M0,n); 
#define D_IO_HighOut_P3(n);	mBIT_0(P3M1,n);mBIT_1(P3M0,n); 
//高阻状态

#define D_IO_HighR_P0(n);	mBIT_1(P0M1,n);mBIT_0(P0M0,n); 
#define D_IO_HighR_P1(n);	mBIT_1(P1M1,n);mBIT_0(P1M0,n); 
#define D_IO_HighR_P2(n);	mBIT_1(P2M1,n);mBIT_0(P2M0,n); 
#define D_IO_HighR_P3(n);	mBIT_1(P3M1,n);mBIT_0(P3M0,n);     

#define D_IO_OpenDrain_P0(n);	mBIT_1(P0M1,n);mBIT_1(P0M0,n); 
#define D_IO_OpenDrain_P1(n);	mBIT_1(P1M1,n);mBIT_1(P1M0,n); 
#define D_IO_OpenDrain_P2(n);	mBIT_1(P2M1,n);mBIT_1(P2M0,n); 
#define D_IO_OpenDrain_P3(n);	mBIT_1(P3M1,n);mBIT_1(P3M0,n);     


//高阻状态
#define P0_conf_in(n)	mBIT_1(P0M1,n);mBIT_0(P0M0,n); 
#define P1_conf_in(n)	mBIT_1(P1M1,n);mBIT_0(P1M0,n); 
#define P2_conf_in(n)	mBIT_1(P2M1,n);mBIT_0(P2M0,n); 
#define P2_conf_port(n)	mBIT_0(P2M1,n);mBIT_0(P2M0,n); 


#define P3_conf_in(n)	mBIT_1(P3M1,n);mBIT_0(P3M0,n); 

#define P3_conf_port(n)	mBIT_0(P3M1,n);mBIT_0(P3M0,n); 


#define P4_conf_in(n)	mBIT_1(P4M1,n);mBIT_0(P4M0,n); 
#define P5_conf_in(n)	mBIT_1(P5M1,n);mBIT_0(P5M0,n); 
#define NOP()	_nop_()



//added by cc
#define D_stdIO_P0_ALL()	P0M1=0;P0M0=0;
#define D_HighI_P0_ALL()	P0M1=0;P0M0=0XFF;
#define D_HighR_P0_ALL()	P0M1=0XFF;P0M0=0;
#define D_OpenD_P0_ALL()	P0M1=0XFF;P0M0=0XFF;

#define D_stdIO_P1_ALL()	P1M1=0;P1M0=0;
#define D_HighI_P1_ALL()	P1M1=0;P1M0=0XFF;
#define D_HighR_P1_ALL()	P1M1=0XFF;P1M0=0;
#define D_OpenD_P1_ALL()	P1M1=0XFF;P1M0=0XFF;

//// n: BITN0---BITN7
#define D_stdIO_P0(BITN)	BITN_0(P0M1,BITN);BITN_0(P0M0,BITN); 	//////00 准双向口 灌电流20mA 拉电流270-150uS 
#define D_HighI_P0(BITN)	BITN_0(P0M1,BITN);BITN_1(P0M0,BITN); //////01 推挽输出 20mA 加限流 
#define D_HighR_P0(BITN)	BITN_1(P0M1,BITN);BITN_0(P0M0,BITN); /////////10  高阻
#define D_OpenD_P0(BITN)	BITN_1(P0M1,BITN);BITN_1(P0M0,BITN); /////11 开漏 open-Drain 内部上拉电阻断开 开漏模式既可以度外部状态也可以对外输出高低电平

#define D_stdIO_P1(BITN)	BITN_0(P1M1,BITN);BITN_0(P1M0,BITN); 	//////00 准双向口 灌电流20mA 拉电流270-150uS 
#define D_HighI_P1(BITN)	BITN_0(P1M1,BITN);BITN_1(P1M0,BITN); //////01 推挽输出 20mA 加限流 
#define D_HighR_P1(BITN)	BITN_1(P1M1,BITN);BITN_0(P1M0,BITN); /////////10  高阻
#define D_OpenD_P1(BITN)	BITN_1(P1M1,BITN);BITN_1(P1M0,BITN); /////11 开漏 open-Drain 内部上拉电阻断开 开漏模式既可以度外部状态也可以对外输出高低电平

#define D_stdIO_P2(BITN)	BITN_0(P2M1,BITN);BITN_0(P2M0,BITN); 	//////00 准双向口 灌电流20mA 拉电流270-150uS 
#define D_HighI_P2(BITN)	BITN_0(P2M1,BITN);BITN_1(P2M0,BITN); //////01 推挽输出 20mA 加限流 
#define D_HighR_P2(BITN)	BITN_1(P2M1,BITN);BITN_0(P2M0,BITN); /////////10  高阻
#define D_OpenD_P2(BITN)	BITN_1(P2M1,BITN);BITN_1(P2M0,BITN); /////11 开漏 open-Drain 内部上拉电阻断开 开漏模式既可以度外部状态也可以对外输出高低电平

#define D_stdIO_P3(BITN)	BITN_0(P3M1,BITN);BITN_0(P3M0,BITN); 	//////00 准双向口 灌电流20mA 拉电流270-150uS 
#define D_HighI_P3(BITN)	BITN_0(P3M1,BITN);BITN_1(P3M0,BITN); //////01 推挽输出 20mA 加限流 
#define D_HighR_P3(BITN)	BITN_1(P3M1,BITN);BITN_0(P3M0,BITN); /////////10  高阻
#define D_OpenD_P3(BITN)	BITN_1(P3M1,BITN);BITN_1(P3M0,BITN); /////11 开漏 open-Drain 内部上拉电阻断开 开漏模式既可以度外部状态也可以对外输出高低电平

#define D_stdIO_P4(BITN)	BITN_0(P4M1,BITN);BITN_0(P4M0,BITN); 	//////00 准双向口 灌电流20mA 拉电流270-150uS 
#define D_HighI_P4(BITN)	BITN_0(P4M1,BITN);BITN_1(P4M0,BITN); //////01 推挽输出 20mA 加限流 
#define D_HighR_P4(BITN)	BITN_1(P4M1,BITN);BITN_0(P4M0,BITN); /////////10  高阻
#define D_OpenD_P4(BITN)	BITN_1(P4M1,BITN);BITN_1(P4M0,BITN); /////11 开漏 open-Drain 内部上拉电阻断开 开漏模式既可以度外部状态也可以对外输出高低电平

#define D_stdIO_P5(BITN)	BITN_0(P5M1,BITN);BITN_0(P5M0,BITN); 	//////00 准双向口 灌电流20mA 拉电流270-150uS 
#define D_HighI_P5(BITN)	BITN_0(P5M1,BITN);BITN_1(P5M0,BITN); //////01 推挽输出 20mA 加限流 
#define D_HighR_P5(BITN)	BITN_1(P5M1,BITN);BITN_0(P5M0,BITN); /////////10  高阻
#define D_OpenD_P5(BITN)	BITN_1(P5M1,BITN);BITN_1(P5M0,BITN); /////11 开漏 open-Drain 内部上拉电阻断开 开漏模式既可以度外部状态也可以对外输出高低电平

#define D_stdIO_P6(BITN)	BITN_0(P6M1,BITN);BITN_0(P6M0,BITN); 	//////00 准双向口 灌电流20mA 拉电流270-150uS 
#define D_HighI_P6(BITN)	BITN_0(P6M1,BITN);BITN_1(P6M0,BITN); //////01 推挽输出 20mA 加限流 
#define D_HighR_P6(BITN)	BITN_1(P6M1,BITN);BITN_0(P6M0,BITN); /////////10  高阻
#define D_OpenD_P6(BITN)	BITN_1(P6M1,BITN);BITN_1(P6M0,BITN); /////11 开漏 open-Drain 内部上拉电阻断开 开漏模式既可以度外部状态也可以对外输出高低电平

#define D_stdIO_P7(BITN)	BITN_0(P7M1,BITN);BITN_0(P7M0,BITN); 	//////00 准双向口 灌电流20mA 拉电流270-150uS 
#define D_HighI_P7(BITN)	BITN_0(P7M1,BITN);BITN_1(P7M0,BITN); //////01 推挽输出 20mA 加限流 
#define D_HighR_P7(BITN)	BITN_1(P7M1,BITN);BITN_0(P7M0,BITN); /////////10  高阻
#define D_OpenD_P7(BITN)	BITN_1(P7M1,BITN);BITN_1(P7M0,BITN); /////11 开漏 open-Drain 内部上拉电阻断开 开漏模式既可以度外部状态也可以对外输出高低电平

#endif

/***

#define P0_conf_in(n)	BITN_1(P0M1,n);BITN_0(P0M0,n); 
#define P1_conf_in(n)	BITN_1(P1M1,n);BITN_0(P1M0,n); 
#define P2_conf_in(n)	BITN_1(P2M1,n);BITN_0(P2M0,n); 
#define P2_conf_port(n)	BITN_0(P2M1,n);BITN_0(P2M0,n); 

#define P3_conf_in(n)	BITN_1(P3M1,n);BITN_0(P3M0,n); 
#define P3_conf_port(n)	BITN_0(P3M1,n);BITN_0(P3M0,n); 

#define P4_conf_in(n)	BITN_1(P4M1,n);BITN_0(P4M0,n); 
#define P5_conf_in(n)	BITN_1(P5M1,n);BITN_0(P5M0,n); 

***/




#define L0_INT4_OPEN()	BITN_1(INT_CLKO, INT_EX4)
#define L0_INT4_CLOSE()	BITN_0(INT_CLKO, INT_EX4)

#define L0_INT4_AT()	BITN_G(INT_CLKO, INT_EX4)




#define L0_INT4_CLEAR()	BITN_0(AUXINTIF, INT4IF)
#define L0_INT3_CLEAR()	BITN_0(AUXINTIF, INT3IF)
#define L0_INT2_CLEAR()	BITN_0(AUXINTIF, INT2IF)




//////

#define L0_INT3_OPEN()	BITN_1(INT_CLKO, INT_EX3);
#define L0_INT3_CLOSE()	BITN_0(INT_CLKO, INT_EX3);
#define L0_INT2_OPEN()	BITN_1(INT_CLKO, INT_EX2);
#define L0_INT2_CLOSE()	BITN_0(INT_CLKO, INT_EX2);
#define L0_INT1_OPEN()	EX1 = 1;
#define L0_INT1_CLOSE()	EX1 = 0;
#define L0_INT0_OPEN()	EX0 = 1;
#define L0_INT0_CLOSE()	EX0 = 0;

#define D_ISR_int0		0		///int0 下降沿触发  = 0 上下沿均可触发
#define D_ISR_timer0	1
#define D_ISR_int1		2		///int1 下降沿触发  = 0 上下沿均可触发
#define D_ISR_timer1 	3
#define D_ISR_int2		10		/////只有下降沿
#define D_ISR_int3		11		/////只有下降沿
#define D_SERVE_UART   	4
#define D_ISR_int4		16		/////只有下降沿

#if 0
#define L0_TIMER1_start()	TR1 = 1;
#define L0_TIMER1_end()		TR1 = 0;


#define L0_TIMER1_isr_OPEN()	ET1 = 1;
#define L0_TIMER1_isr_CLOSE()	ET1 = 0;


#else

#define L0_TIMER1_start()	ET1 = 1;
#define L0_TIMER1_end()		ET1 = 0;


#define L0_TIMER1_isr_OPEN()	TR1 = 1;
#define L0_TIMER1_isr_CLOSE()	TR1 = 0;


#endif

/// fixme  颠倒定义会让c51锁死#define _nop_() 	NOP()

///#define L0_INT3_OPEN()	BITN_1(INT_CLKO,INT_EX3);             	//使能INT3中断
///#define L0_INT3_CLOSE()	BITN_0(INT_CLKO,INT_EX3);
#endif	//STC_stc8a8k