//////////////////////////////////////////////////////////////////////////// ///@copyright Copyright (c) 2017, 传控科技 All rights reserved. ///------------------------------------------------------------------------- /// @file hard_config.h /// @brief hard config include /// @info FILE FOR HARDWARE SETUP AND SOFTWARE SETUP///FOR EXAMPLE: BAORD ,MCU,IDE /// @info YOU CAN CHANGE OR ADD THE DEFINE IF YOU NEED /// @info 整个嵌入式项目的入口 首先是确认电路板 然后确认cpu 芯片型号 然后确认编译器 之后是软件框架 最后是应用程序 /// @info bsp_CONFIG 为其他头文件的始祖 TYPE_BOARD_xx ///------------------------------------------------------------------------- /// @version 1.1 /// @author CC /// @date 20180308 /// @note ////////////////////////////////////////////////////////////////////////////// /// @version 5.1 /// @author CC /// @date 20200301 /// @note ////////////////////////////////////////////////////////////////////////////// ////////////////////////////////////////////////////////////////////////// #ifndef _BSP_CONFIG_H #define _BSP_CONFIG_H #include #include "../clib/type.h" #include "../clib/bit.h" //>>>>>>>>>>>>>>>>>>>>>>.BORAD TYPE #define TYPE_BOARD_hhnew 1 #define TYPE_BOARD_st_sleep04_01 4 #define TYPE_BOARD_st_sleep03 5 #define TYPE_BOARD_SMMM_MB_VH032_0E 6 #define TYPE_BOARD_LPC17xx_ 8 #define TYPE_BOARD_STM32F_103ZET6_READBULL 1036 #define TYPE_BOARD_hh_CC_MD_VH05_anyriny_simple_m51 0x0551 #define TYPE_BOARD_hh_CC_MD_VH06_asMain_m6a7 0x6a7 #define TYPE_BOARD_TI26_MT01_M178 0x178 //会议计时器版v TI26_MT01-M178 #define TYPE_BOARD_stc5as32_WIFIBV01 532 #define TYPE_BOARD_SHC16LAXXQN32 1632 //SHC16LAXXQN32 #define TYPE_BOARD_PAPER6133_M0A6 0xa6 //打印机纸张传感 #define TYPE_BOARD_GSM_MAIN_V07 0xa7 //打印机运维板 #define TYPE_BOARD_ADDA_MAIN_V02 0xa8 //ADDA #define TYPE_BOARD_433_0A 0xa9 //433 #define TYPE_BOARD_WEIGH_0B 0xaa //称重 //<<<<<<<<<<<<<<<<<<<<<<<<<<<.BORAD TYPE end //>>>>>>>>>>>>>>>>>>>>>>MCU TYPE #define TYPE_MCU_STC_8A 51 #define TYPE_MCU_STC_8F 52 #define TYPE_MCU_STC_8G 53 #define TYPE_MCU_SHC6601 66 #define TYPE_MCU_LPC17xx 3217 #define TYPE_MCU_STM32 3232 #define D_CPUfamily_8bits 8 #define D_CPUfamily_16bits 16 #define D_CPUfamily_32bits 32 //<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>>>IDE TYPE #define TYPE_IDE_KEIL 1 #define TYPE_IDE_MDK 2 #define TYPE_IDE_IAR 3 //<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>>>.SysTimer TYPE #define TYPE_JIFFIES_5MS 1 #define TYPE_JIFFIES_10MS 2 #define TYPE_JIFFIES_25MS 3 //<<<<<<<<<<<<<<<<<<<<<<<<<<<.SysTimer TYPE end //>>>>>>>>>>>>>>>>>>>>>>.WDT TYPE #define TYPE_WDT_DISABLE 1 #define TYPE_WDT_ENABLE 2 #define WDT_FEED() WDT_CONTR |= 0x10 //<<<<<<<<<<<<<<<<<<<<<<<<<<<.SysTimer TYPE end //>>>>>>>>>>>>>>>>>>>>>>.ByteOrder TYPE #define TYPE_MCU_BIGENDIAN 1 #define TYPE_MCU_LITENDIAN 2 //<<<<<<<<<<<<<<<<<<<<<<<<<<<.ByteOrder TYPE end //>>>>>>>>>>>>>>>>>>>>>>BUADRATE & StopBit #define SBIT_1 1 //1 stop bit #define SBIT_2 2 //2 stop bit #define BRT_115200 115200 #define BRT_19200 19200 #define BRT_9600 9600 #define BRT_4800 4800 //<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>>>MainFre #define MainFre_5M 5529600L #define MainFre_11M 11059200L #define MainFre_22M 22118400L #define MainFre_24M 24000000L #define MainFre_27M 27000000L //<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>>>UART0 PIN #define PIN_UART0_Rxd_30_Txd_31 1 #define PIN_UART0_Rxd_36_Txd_37 2 #define PIN_UART0_Rxd_16_Txd_17 3 #define PIN_UART0_Rxd_43_Txd_44 4 //<<<<<<<<<<<<<<<<<<<<<<<<<<<.UART0 PIN //>>>>>>>>>>>>>>>>>>>>>>485 Type #define TYPE_485_NONE 0 #define TYPE_485_MASTER 1 #define TYPE_485_SLAVER 2 //<<<<<<<<<<<<<<<<<<<<<<485 Type end //>>>>>>>>>>>>>>>>>>>>>>G-SENSOR TYPE #define TYPE_ASENSOR_ADXL362 362 #define TYPE_ASENSOR_MSA300 300 #define TYPE_ASENSOR TYPE_ASENSOR_MSA300 //<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> #define TYPE_UASER_BOARD TYPE_BOARD_WEIGH_0B //STEP 2 TYPE_UASER_BOARD CONFIG >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> #if(TYPE_UASER_BOARD == TYPE_BOARD_WEIGH_0B) #include #include #include #include "../cpu/stc_stc8f.h" #include "../cpu/stc_macro.h" //基本配置(工作频率、时钟、看门狗、字节序) #define TYPE_MCU TYPE_MCU_STC_8F #define TYPE_IDE TYPE_IDE_KEIL #define D_CPUfamily_type D_CPUfamily_8bits #define D_sys_MainFre MainFre_11M #define D_sys_Jiffies TYPE_JIFFIES_10MS #define D_WDT_STATUS TYPE_WDT_DISABLE //如果配置为enable，请在bsp_config.c中设置wdt溢出时间 #define D_MCU_ENDIAN TYPE_MCU_BIGENDIAN //串口配置 #define D_uart0_BRT BRT_115200 #define D_uart0_SBIT SBIT_1 #define D_PIN_UART0 PIN_UART0_Rxd_30_Txd_31 #define D_uart2_BRT BRT_115200 #define D_uart3_BRT BRT_115200 #define D_uart4_BRT BRT_115200 //485配置 #define D_UART0_485_TYPE TYPE_485_SLAVER //UART0启用485 #define D_UART0_485_SLAVER_ID_BROADCAST 0xFF //485从机总是响应0xFF消息 #define D_UART0_485_SLAVER_ID 0x01 //板卡作为485从机 slaverId #define D_UART0_485_TX() P32 = 1; #define D_UART0_485_RX() P32 = 0; #define D_UART2_485_TYPE TYPE_485_NONE //UART2不启用485 #define D_UART3_485_TYPE TYPE_485_NONE //UART2不启用485 #define D_UART4_485_TYPE TYPE_485_NONE //UART2不启用485 //MODBUS协议配置 #define D_MODBUS_ENABLE //MODBS启用开关，如果不使用modbus，可以注释掉本行 #define D_MODBUS_SPLIT_ENTRY L1_modbus_split //modbus切割函数，在tpc_modbus.c中实现，依据实际情况修改 #define D_MODBUS_REG_MAX_NUM 32 //每次最多读取/写入的寄存器数量，此处的数量要注意和 D_tp_handle_x_len 对应 //外设定义 #define LED0 P10 //D4 #define LED1 P35 //D4 //EEP存储地址定义 #define D_EEP_SECTOR_SIZE 0x200 #define D_EEP_PARAM_ADDR (D_EEP_SECTOR_SIZE * 0) //eeprom参数区扇区地址 #if(MainFre_5M == D_sys_MainFre) #define D_Cdelay_200us 20 #define D_Cdelay_1us 1 ////while p21翻转时测定 500k 2us 一个指令 #elif(MainFre_22M == D_sys_MainFre) #define D_Cdelay_200us 20 #define D_Cdelay_1us 1 ////while p21翻转时测定 500k 2us 一个指令 #define D_Cdelay_1us 1 ////while p21翻转时测定 500k 2us 一个指令 #define L0_delay_1us() Lc_delay_nop(0) // 5个nop() 100ns 50个nop() 1us (20)=10us (2)1.5us #define L0_delay_10us() Lc_delay_nop(4) // 5个nop() 100ns 50个nop() 1us (20)=10us (2)1.5us #define L0_delay_40us() Lc_delay_nop(18) // 5个nop() 100ns 50个nop() 1us (20)=10us (2)1.5us #elif(MainFre_27M == D_sys_MainFre) #define D_Cdelay_200us 20 #define D_Cdelay_1us 1 ////while p21翻转时测定 500k 2us 一个指令 #else ///MainFre_11M #define D_Cdelay_200us 20 #define D_Cdelay_1us 1 ////while p21翻转时测定 500k 2us 一个指令 #define L0_delay_1us() Lc_delay_nop(0) // 5个nop() 100ns 50个nop() 1us (20)=10us (2)1.5us #define L0_delay_10us() Lc_delay_nop(4) // 5个nop() 100ns 50个nop() 1us (20)=10us (2)1.5us #define L0_delay_40us() Lc_delay_nop(18) // 5个nop() 100ns 50个nop() 1us (20)=10us (2)1.5us //xx #endif//D_sys_MainFre) #elif(TYPE_UASER_BOARD == TYPE_BOARD_433_0A) xxx #endif //STEP 3 Register CONFIG >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> #if 0 序号 量程 系数 1 100kg 100% 2 200kg 100% 3 300kg 100% 4 400kg 100% 5 500kg 100% 6 600kg 100% 7 700kg 100% 8 800kg 100% 9 900kg 100% 10 1000kg 100% #endif #define ADC_status_chx_Ready_BASE 0x01 #define ADC_status_ch1_Ready 0x01 #define ADC_status_ch2_Ready 0x02 #define ADC_status_ch3_Ready 0x04 #define ADC_status_ch4_Ready 0x08 #define D_weight_show_limit_num 5 #define D_weight_std_num 10 typedef struct global_register { //RO Register S16 reserved1; S32 total_weight; //净重（显示重量）*100 S32 total_zweight; //皮重*100 //RW Register S16 reserved2; struct { //需要持久化的参数，不能超过72字节，否则会导致eeprom溢出 U16 reset; //reset标志，写入任何值，所有参数恢复初始值 U16 adc_ch_status; S16 slaver_id; S16 zero; //清0标志，写入任何值清0（去皮） S16 weight_max; //量程 S16 lmd; //2mv/v S16 cc_blur_ch_avg; //均值滤波点数 S16 cc_blur_ch_shift; //移位滤波点数 S16 cc_blur_all_shift0; //和值移位滤波点数1 S16 cc_blur_all_shift1; //和值移位滤波点数2 S16 cc_blur_all_out_d_threshold; //移位阈值1 S16 cc_blur_all_out_dd_threshold;//移位阈值2 struct{ S16 weight; S16 times; } weight_show_limit[D_weight_show_limit_num]; struct { S16 weight_range; //量程 x 100 S16 ratio; //重量计算系数，默认100，保留两位小数，相当于x1 } weight_std[D_weight_std_num]; U16 baud_rate; //波特率 U16 stop_bits; //停止位 }p; S16 reserved3; }GlobalRegister; //寄存器内存基地址 #define REG_MEM_BASE ((U16*)(&R)) //寄存器基础地址（本文件外部不应该使用该宏定义） //变量地址转寄存器 #define MEM_2_REG(mem) (((U16*)(mem) - REG_MEM_BASE) + 1) //寄存器转变量地址 #define REG_2_MEM(reg) (REG_MEM_BASE + (U16)((reg) - 1)) extern GlobalRegister R; //Step4: IRQ Config #if (TYPE_MCU == TYPE_MCU_STC_8A || TYPE_MCU == TYPE_MCU_STC_8F) #define D_SERVE_INT0 interrupt 0 #define D_SERVE_TIMER0 interrupt 1 #define D_SERVE_INT1 interrupt 2 #define D_SERVE_TIMER1 interrupt 3 #define D_SERVE_UART interrupt 4 #define D_SERVE_ADC interrupt 5 #define D_SERVE_LVD interrupt 6 #define D_SERVE_PCA interrupt 7 #define D_SERVE_UART2 interrupt 8 #define D_SERVE_SPI interrupt 9 #define D_SERVE_INT2 interrupt 10 #define D_SERVE_INT3 interrupt 11 #define D_SERVE_TIMER2 interrupt 12 #define D_SERVE_INT4 interrupt 16 #define D_SERVE_UART3 interrupt 17 #define D_SERVE_UART4 interrupt 18 #define D_SERVE_TIMER3 interrupt 19 #define D_SERVE_TIMER4 interrupt 20 #define D_SERVE_CMP interrupt 21 #define D_SERVE_PWM interrupt 22 #define D_SERVE_PWMFD interrupt 23 #define D_SERVE_I2C interrupt 24 #endif //======================================================== 以下为协议配置 ==================================================== #define D_CMD_Filter1_ff 0xFF #define D_CMD_Filter2_fe 0xFE #define D_HETU_FX_fi 0xF0 #define D_HETU_FX_MASK 0x0F #define D_tp_handle_x_len 64 extern void L0_board_config(void); extern void L0_reg_init(void); #endif//_BSP_CONFIG_H /*********************************end file*********************************************/