#include "bsp_config.h"
#include "../tpc/tpc_modbus.h"

////////////////////////////////////////////////////////////////////////////  
///@copyright  Copyright (c) 2018, 传控科技 All rights reserved.  
///-------------------------------------------------------------------------  
/// @file            bsp_func.c
/// @brief           bsp @ fuctiong ;  io复用选择等，和cpu型号息息相关
///-------------------------------------------------------------------------  
/// @version		1.0  
/// @author			CC 
/// @date			20180308
/// @note			cc_AS_stc02

//////////////////////////////////////////////////////////////////////////////
//struct _s_sysclk s_sysclk;

GlobalRegister R;

void L0_reg_reset()
{
	U8 i = 0;
	//R.p.reset = 0;
	R.p.adc_ch_status = ADC_status_ch2_Ready | ADC_status_ch3_Ready | ADC_status_ch4_Ready;		//修改采集通道
	R.p.slaver_id = D_UART0_485_SLAVER_ID;	
	//R.p.zero = 0;
	R.p.weight_max = 500;	//500kg
	R.p.lmd = 2;	//2mv/v
	
	R.p.cc_blur_ch_avg = 6;
	R.p.cc_blur_ch_shift = 2;
	R.p.cc_blur_all_shift0 = 2;
	R.p.cc_blur_all_shift1 = 4;
	R.p.cc_blur_all_out_d_threshold = 200;	//0.2kg
	R.p.cc_blur_all_out_dd_threshold = 200;	//0.2kg

	for(i=0;i<D_weight_show_limit_num;i++)
	{
		R.p.weight_show_limit[i].weight = 0;
		R.p.weight_show_limit[i].times = 0;
	}
	R.p.weight_show_limit[0].weight = 300;	//0.3kg
	R.p.weight_show_limit[0].times = 1;
	R.p.weight_show_limit[1].weight = 200;	//0.2kg
	R.p.weight_show_limit[1].times = 9;
	R.p.weight_show_limit[2].weight = 100;	//0.1kg
	R.p.weight_show_limit[2].times = 18;
	R.p.weight_show_limit[3].weight = 50;	//0.05kg
	R.p.weight_show_limit[3].times = 18;
	R.p.weight_show_limit[4].weight = 20;	//0.02kg
	R.p.weight_show_limit[4].times = 30;
	
	//for(i=0;i<D_weight_std_num;i++)
	//{
	//	R.p.weight_std[i].weight_range = 0;
	//	R.p.weight_std[i].ratio = 0;
	//}

	R.p.baud_rate = 19200;
	R.p.stop_bits = 1;
}

void L0_reg_init(void)
{
	R.reserved1 = R.reserved2 = R.reserved3 = 0x55;
	//R.total_weight = R.total_zweight = 0;
	L0_reg_reset();
}

//==========================================================
//系统定时器回调
//初始化为NULL，timer0_isr中判断为NULL则不调用
//==========================================================


void L0_board_config(void)
{
#if (PIN_UART0_Rxd_30_Txd_31 == D_PIN_UART0)
	BITN_0(P_SW1 ,BITN7);//
	BITN_0(P_SW1 ,BITN6);// rxd p3.0 txd p3.1
#elif (PIN_UART0_Rxd_36_Txd_37 == D_PIN_UART0)
	BITN_0(P_SW1 ,BITN7);//
	BITN_1(P_SW1 ,BITN6);// rxd p3.6 txd p3.7
#elif (PIN_UART0_Rxd_16_Txd_17 == D_PIN_UART0)
	BITN_1(P_SW1 ,BITN7);//
	BITN_0(P_SW1 ,BITN6);// rxd p1.6 txd p1.7
#elif (PIN_UART0_Rxd_43_Txd_44 == D_PIN_UART0)
	BITN_1(P_SW1 ,BITN7);//
	BITN_1(P_SW1 ,BITN6);// rxd p4.3 txd p4.4
#else
	BITN_0(P_SW1 ,BITN7);//
	BITN_0(P_SW1 ,BITN6);// rxd p3.0 txd p3.1
#endif

	//uart2
	BITN_0(P_SW2 ,BITN0);// rxd2 p1.0 txd2 p1.1	
	//BITN_1(P_SW2 ,BITN0);// rxd2 p4.0 txd2 p4.2

	//uart3
	//P_SW2 = 0x02; // RXD3_2/P5.0, TXD3_2/P5.1

	//uart4
	//BITN_1(P_SW2 ,BITN2);// rxd4 p5.2 txd4 p5.3	
	//BITN_0(P_SW2 ,BITN2);// rxd4 p0.2 txd4 p0.3

	//485 RE/DE 配置推完输出 P32
	BITN_0(P3M1,BITN2);BITN_1(P3M0,BITN2);

	#if (TYPE_WDT_ENABLE == D_WDT_STATUS)
	WDT_CONTR = 0x27;     //使能看门狗,22M时钟下溢出时间约为5s，请注意添加喂狗程序
	#else
	WDT_CONTR = 0x00;  
	#endif

	//Lp0_Sys_timer_extern_handler被timer0中断调用
	//Lp0_Sys_timer_extern_handler = L1_Sys_timer_extern_handler;
}