stc_ttss_868/source/bsp/bsp_config.h

////////////////////////////////////////////////////////////////////////////  
///@copyright  Copyright (c) 2017, 传控科技 All rights reserved.  
///-------------------------------------------------------------------------  
/// @file            hard_config.h
/// @brief           hard config include
/// @info  FILE FOR HARDWARE SETUP AND SOFTWARE SETUP///FOR EXAMPLE: BAORD ,MCU,IDE
/// @info  YOU CAN CHANGE OR ADD THE DEFINE IF YOU NEED
/// @info  整个嵌入式项目的入口  首先是确认电路板  然后确认cpu 芯片型号  然后确认编译器  之后是软件框架  最后是应用程序  
/// @info    bsp_CONFIG  为其他头文件的始祖 TYPE_BOARD_xx
///-------------------------------------------------------------------------  
/// @version		1.1  
/// @author		CC 
/// @date			20180308
/// @note			
//////////////////////////////////////////////////////////////////////////////
/// @version		5.1  
/// @author		CC 
/// @date			20200301
/// @note			
//////////////////////////////////////////////////////////////////////////////


//////////////////////////////////////////////////////////////////////////
#ifndef   _BSP_CONFIG_H
#define   _BSP_CONFIG_H

#include <INTRINS.H>
#include "../clib/type.h"
#include "../clib/bit.h"

//>>>>>>>>>>>>>>>>>>>>>>.BORAD TYPE
#define TYPE_BOARD_hhnew			1
#define	TYPE_BOARD_st_sleep04_01		4
#define	TYPE_BOARD_st_sleep03		5
#define TYPE_BOARD_SMMM_MB_VH032_0E	6
#define TYPE_BOARD_LPC17xx_	8
#define TYPE_BOARD_STM32F_103ZET6_READBULL	1036
#define TYPE_BOARD_hh_CC_MD_VH05_anyriny_simple_m51		0x0551
#define TYPE_BOARD_hh_CC_MD_VH06_asMain_m6a7		0x6a7
#define TYPE_BOARD_TI26_MT01_M178	0x178		//会议计时器版v TI26_MT01-M178
#define TYPE_BOARD_stc5as32_WIFIBV01	532
#define TYPE_BOARD_SHC16LAXXQN32		1632		//SHC16LAXXQN32
#define TYPE_BOARD_PAPER6133_M0A6		0xa6		//打印机纸张传感
#define TYPE_BOARD_GSM_MAIN_V07			0xa7		//打印机运维板
#define TYPE_BOARD_ADDA_MAIN_V02		0xa8		//ADDA
#define TYPE_BOARD_433_0A				0xa9		//433
#define TYPE_BOARD_WEIGH_0B				0xaa		//称重
//<<<<<<<<<<<<<<<<<<<<<<<<<<<.BORAD TYPE end

//>>>>>>>>>>>>>>>>>>>>>>MCU TYPE
#define TYPE_MCU_STC_8A		51
#define TYPE_MCU_STC_8F		52
#define TYPE_MCU_STC_8G		53
#define TYPE_MCU_SHC6601	66
#define TYPE_MCU_LPC17xx	3217
#define TYPE_MCU_STM32		3232

#define D_CPUfamily_8bits	8
#define D_CPUfamily_16bits	16
#define D_CPUfamily_32bits	32
//<<<<<<<<<<<<<<<<<<<<<<mcu TYPE end

//>>>>>>>>>>>>>>>>>>>>>>IDE TYPE
#define TYPE_IDE_KEIL	1
#define TYPE_IDE_MDK	2
#define TYPE_IDE_IAR	3
//<<<<<<<<<<<<<<<<<<<<<<IDE TYPE end

//>>>>>>>>>>>>>>>>>>>>>>.SysTimer TYPE
#define TYPE_JIFFIES_5MS	1
#define TYPE_JIFFIES_10MS	2
#define TYPE_JIFFIES_25MS	3
//<<<<<<<<<<<<<<<<<<<<<<<<<<<.SysTimer TYPE end

//>>>>>>>>>>>>>>>>>>>>>>.WDT TYPE
#define TYPE_WDT_DISABLE	1
#define TYPE_WDT_ENABLE		2
#define WDT_FEED()  WDT_CONTR |= 0x10
//<<<<<<<<<<<<<<<<<<<<<<<<<<<.SysTimer TYPE end

//>>>>>>>>>>>>>>>>>>>>>>.ByteOrder TYPE
#define TYPE_MCU_BIGENDIAN	1
#define TYPE_MCU_LITENDIAN	2
//<<<<<<<<<<<<<<<<<<<<<<<<<<<.ByteOrder TYPE end

//>>>>>>>>>>>>>>>>>>>>>>BUADRATE & StopBit
#define SBIT_1 1	//1 stop bit
#define SBIT_2 2	//2 stop bit
#define BRT_115200 115200
#define BRT_19200  19200
#define BRT_9600   9600
#define BRT_4800   4800
//<<<<<<<<<<<<<<<<<<<<<<BUADRATE & StopBit end

//>>>>>>>>>>>>>>>>>>>>>>MainFre
#define MainFre_5M  5529600L
#define MainFre_11M 11059200L
#define MainFre_22M 22118400L
#define MainFre_24M 24000000L
#define MainFre_27M 27000000L
//<<<<<<<<<<<<<<<<<<<<<<MainFre end

//>>>>>>>>>>>>>>>>>>>>>>UART0 PIN
#define PIN_UART0_Rxd_30_Txd_31		1
#define PIN_UART0_Rxd_36_Txd_37		2
#define PIN_UART0_Rxd_16_Txd_17  	3
#define PIN_UART0_Rxd_43_Txd_44  	4
//<<<<<<<<<<<<<<<<<<<<<<<<<<<.UART0 PIN

//>>>>>>>>>>>>>>>>>>>>>>485 Type
#define TYPE_485_NONE	0
#define TYPE_485_MASTER	1
#define TYPE_485_SLAVER	2
//<<<<<<<<<<<<<<<<<<<<<<485 Type end

//>>>>>>>>>>>>>>>>>>>>>>G-SENSOR TYPE
#define TYPE_ASENSOR_ADXL362	362
#define TYPE_ASENSOR_MSA300		300
#define TYPE_ASENSOR	TYPE_ASENSOR_MSA300
//<<<<<<<<<<<<<<<<<<<<<<G-SENSOR TYPE end

//STEP 1 TYPE_UASER_BOARD SELECT >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
#define TYPE_UASER_BOARD	TYPE_BOARD_WEIGH_0B

//STEP 2 TYPE_UASER_BOARD CONFIG >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
#if(TYPE_UASER_BOARD == TYPE_BOARD_WEIGH_0B)
	#include <stdio.h>
	#include <string.h>
	#include <intrins.h>
	#include "../cpu/stc_stc8f.h"
	#include "../cpu/stc_macro.h"
	
	//基本配置(工作频率、时钟、看门狗、字节序)
	#define TYPE_MCU	TYPE_MCU_STC_8F
	#define TYPE_IDE	TYPE_IDE_KEIL
	#define D_CPUfamily_type	D_CPUfamily_8bits
	#define D_sys_MainFre	MainFre_11M
	#define D_sys_Jiffies	TYPE_JIFFIES_10MS
	#define D_WDT_STATUS	TYPE_WDT_DISABLE	//如果配置为enable，请在bsp_config.c中设置wdt溢出时间
	#define D_MCU_ENDIAN	TYPE_MCU_BIGENDIAN
	
	//串口配置
	#define D_uart0_BRT 	BRT_115200
	#define D_uart0_SBIT 	SBIT_1
	#define D_PIN_UART0		PIN_UART0_Rxd_30_Txd_31
	#define D_uart2_BRT 	BRT_115200
	#define D_uart3_BRT 	BRT_115200
	#define D_uart4_BRT 	BRT_115200
	
	//485配置
	#define D_UART0_485_TYPE TYPE_485_SLAVER	//UART0启用485
	#define D_UART0_485_SLAVER_ID_BROADCAST 0xFF	//485从机总是响应0xFF消息
	#define D_UART0_485_SLAVER_ID 0x01			//板卡作为485从机 slaverId
	#define D_UART0_485_TX()		P32 = 1;
	#define D_UART0_485_RX()		P32 = 0;
	#define D_UART2_485_TYPE TYPE_485_NONE	//UART2不启用485
	#define D_UART3_485_TYPE TYPE_485_NONE	//UART2不启用485
	#define D_UART4_485_TYPE TYPE_485_NONE	//UART2不启用485
	
	//MODBUS协议配置
	#define D_MODBUS_ENABLE	//MODBS启用开关，如果不使用modbus，可以注释掉本行
	#define D_MODBUS_SPLIT_ENTRY 	L1_modbus_split		//modbus切割函数，在tpc_modbus.c中实现，依据实际情况修改
	#define D_MODBUS_REG_MAX_NUM 	32 	//每次最多读取/写入的寄存器数量，此处的数量要注意和 D_tp_handle_x_len 对应
	
	//外设定义
	#define LED0	P10		//D4
	#define LED1	P35		//D4
	
	//EEP存储地址定义
	#define D_EEP_SECTOR_SIZE 0x200
	#define D_EEP_PARAM_ADDR (D_EEP_SECTOR_SIZE * 0)	//eeprom参数区扇区地址
	
	#if(MainFre_5M == D_sys_MainFre)
	#define D_Cdelay_200us		20
	#define D_Cdelay_1us		1		////while p21翻转时测定  500k 2us 一个指令
	#elif(MainFre_22M == D_sys_MainFre)	
	#define D_Cdelay_200us		20
	#define D_Cdelay_1us		1		////while p21翻转时测定  500k 2us 一个指令
	#define D_Cdelay_1us		1		////while p21翻转时测定  500k 2us 一个指令
	#define L0_delay_1us()	Lc_delay_nop(0)		// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
	#define L0_delay_10us()	Lc_delay_nop(4)		// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
	#define L0_delay_40us()	Lc_delay_nop(18)	// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
	#elif(MainFre_27M == D_sys_MainFre)
	#define D_Cdelay_200us		20
	#define D_Cdelay_1us		1		////while p21翻转时测定  500k 2us 一个指令
	#else		///MainFre_11M	
	#define D_Cdelay_200us		20
	#define D_Cdelay_1us		1		////while p21翻转时测定  500k 2us 一个指令
	#define L0_delay_1us()	Lc_delay_nop(0)		// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
	#define L0_delay_10us()	Lc_delay_nop(4)		// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
	#define L0_delay_40us()	Lc_delay_nop(18)	// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
			//xx
	#endif//D_sys_MainFre)

#elif(TYPE_UASER_BOARD == TYPE_BOARD_433_0A)
	xxx
#endif


//STEP 3 Register CONFIG >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>


#if 0
序号    量程		系数
1     100kg		100%
2     200kg		100%
3     300kg		100%
4     400kg		100%
5     500kg 	100%
6     600kg		100%
7     700kg		100%
8     800kg		100%
9     900kg		100%
10    1000kg 	100%
#endif

#define ADC_status_chx_Ready_BASE 0x01
#define ADC_status_ch1_Ready 0x01
#define ADC_status_ch2_Ready 0x02
#define ADC_status_ch3_Ready 0x04
#define ADC_status_ch4_Ready 0x08

#define D_weight_show_limit_num 5
#define D_weight_std_num 10
typedef struct global_register
{
	//RO Register
	S16 reserved1;
	S32 total_weight;	//净重（显示重量）*100
	S32 total_zweight;	//皮重*100
	//RW Register
	S16 reserved2;
	struct {	//需要持久化的参数，不能超过72字节，否则会导致eeprom溢出
		U16 reset;	//reset标志，写入任何值，所有参数恢复初始值
		U16 adc_ch_status;
		S16 slaver_id;
		S16 zero;	//清0标志，写入任何值清0（去皮）
		S16 weight_max;  //量程
		S16 lmd;	//2mv/v
		S16 cc_blur_ch_avg; //均值滤波点数
		S16 cc_blur_ch_shift;	//移位滤波点数
		S16 cc_blur_all_shift0; //和值移位滤波点数1
		S16 cc_blur_all_shift1; //和值移位滤波点数2
		S16 cc_blur_all_out_d_threshold;	//移位阈值1
		S16 cc_blur_all_out_dd_threshold;//移位阈值2
		struct{
			S16 weight;
			S16 times;
		} weight_show_limit[D_weight_show_limit_num];
		struct {
			S16 weight_range;	//量程 x 100
			S16 ratio;			//重量计算系数，默认100，保留两位小数，相当于x1
		} weight_std[D_weight_std_num];
		U16 baud_rate;	//波特率
		U16 stop_bits;	//停止位
	}p;
	S16 reserved3;
}GlobalRegister;

//寄存器内存基地址
#define REG_MEM_BASE                ((U16*)(&R))	//寄存器基础地址（本文件外部不应该使用该宏定义）
//变量地址转寄存器
#define MEM_2_REG(mem)              (((U16*)(mem) - REG_MEM_BASE) + 1)
//寄存器转变量地址
#define REG_2_MEM(reg)              (REG_MEM_BASE + (U16)((reg) - 1))

extern GlobalRegister R;

//Step4: IRQ Config
#if (TYPE_MCU == TYPE_MCU_STC_8A || TYPE_MCU == TYPE_MCU_STC_8F)
#define D_SERVE_INT0	interrupt 0
#define D_SERVE_TIMER0	interrupt 1
#define D_SERVE_INT1   	interrupt 2
#define D_SERVE_TIMER1	interrupt 3
#define D_SERVE_UART	interrupt 4
#define D_SERVE_ADC		interrupt 5
#define D_SERVE_LVD		interrupt 6
#define D_SERVE_PCA		interrupt 7
#define D_SERVE_UART2	interrupt 8
#define D_SERVE_SPI		interrupt 9
#define D_SERVE_INT2	interrupt 10
#define D_SERVE_INT3	interrupt 11
#define D_SERVE_TIMER2	interrupt 12
#define D_SERVE_INT4	interrupt 16
#define D_SERVE_UART3   interrupt 17
#define D_SERVE_UART4	interrupt 18

#define D_SERVE_TIMER3  interrupt 19
#define D_SERVE_TIMER4  interrupt 20
#define D_SERVE_CMP  	interrupt 21
#define D_SERVE_PWM   	interrupt 22
#define D_SERVE_PWMFD   interrupt 23
#define D_SERVE_I2C   	interrupt 24
#endif

//======================================================== 以下为协议配置 ====================================================
#define D_CMD_Filter1_ff 	0xFF
#define D_CMD_Filter2_fe 	0xFE
#define D_HETU_FX_fi	0xF0
#define D_HETU_FX_MASK	0x0F
#define D_tp_handle_x_len 64

extern void L0_board_config(void);
extern void L0_reg_init(void);

#endif//_BSP_CONFIG_H
/*********************************end file*********************************************/