DDB/source/bsp/bsp_config.h

////////////////////////////////////////////////////////////////////////////  
///@copyright  Copyright (c) 2017, 传控科技 All rights reserved.  
///-------------------------------------------------------------------------  
/// @file            bsp_config.h
/// @brief           hard config include
/// @info  FILE FOR HARDWARE SETUP AND SOFTWARE SETUP///FOR EXAMPLE: BAORD ,MCU,IDE
/// @info  YOU CAN CHANGE OR ADD THE DEFINE IF YOU NEED
/// @info  整个嵌入式项目的入口  首先是确认电路板  然后确认cpu 芯片型号  然后确认编译器  之后是软件框架  最后是应用程序  
/// @info    bsp_CONFIG  为其他头文件的始祖 TYPE_BOARD_xx
///-------------------------------------------------------------------------  
/// @version		1.1  
/// @author			CC 
/// @date			20180308
/// @note			
//////////////////////////////////////////////////////////////////////////////
/// @version		5.1  
/// @author			CC 
/// @date			20200301
/// @note			
//////////////////////////////////////////////////////////////////////////////


//////////////////////////////////////////////////////////////////////////
///存储器中的特殊参数
///全球唯一ID号 7FF9H~7FFFH BFF9H~BFFFH EFF9H~EFFFH FDF9H~FDFFH 7字节
///内部1.19V参考信号源 7FF7H~7FF8H BFF7H~BFF8H EFF7H~EFF8H FDF7H~FDF8H 毫伏（高字节在前）
///32K掉电唤醒定时器的频率 7FF5H~7FF6H BFF5H~BFF6H EFF5H~EFF6H FDF5H~FDF6H Hz （高字节在前）
///22.1184MHz的IRC参数（20M频段） 7FF4H BFF4H EFF4H FDF4H －
///24MHz的IRC参数（20M频段） 7FF3H BFF3H EFF3H FDF3H －
///20MHz的IRC参数（20M频段） 7FF2H BFF2H EFF2H FDF2H
///固件版本为7.3.12U
///以及后续版本有效
///27MHz的IRC参数（35M频段） 7FF1H BFF1H EFF1H FDF1H
///30MHz的IRC参数（35M频段） 7FF0H BFF0H EFF0H FDF0H
///33.1776MHz的IRC参数（35M频段） 7FEFH BFEFH EFEFH FDEFH
///35MHz的IRC参数（35M频段） 7FEEH BFEEH EFEEH FDEEH
///36.864MHz的IRC参数（35M频段） 7FEDH BFEDH EFEDH FDEDH
///保留 7FECH BFECH EFECH FDECH
///保留 7FEBH BFEBH EFEBH FDEBH
///20M频段的VRTRIM参数 7FEAH BFEAH EFEAH FDEAH
///35M频段的VRTRIM参数 7FE9H BFE9H EFE9H FDE9H
//////////////////////////////////////////////////////////////////////////

#ifndef   _BSP_CONFIG_H
#define   _BSP_CONFIG_H

#include <INTRINS.H>
#include "../bsp/bsp_config_const.h"
#include "../clib/type.h"
#include "../clib/bit.h"


//STEP 1 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>TYPE_UASER_BOARD SELECT
#define TYPE_UASER_BOARD	TYPE_BOARD_TOUCH_PEN_0C
//STEP 1 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<YPE_UASER_BOARD SELECT End





//STEP 2 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>TYPE_UASER_BOARD CONFIG 
#if(TYPE_UASER_BOARD == TYPE_BOARD_TOUCH_PEN_0C)
	#include <intrins.h>
//	#include "../cpu/stc_stc8hxx.h"
//	#include "../cpu/stc_macro.h"
	
	//基本配置(工作频率、时钟、看门狗、字节序)
	#define TYPE_MCU	TYPE_MCU_STC_8H
	#define TYPE_IDE	TYPE_IDE_KEIL
	#define D_CPUfamily_type	D_CPUfamily_8bits
	#define D_sys_MainFre	MainFre_22M
	#define D_sys_Jiffies	TYPE_JIFFIES_10MS
	#define D_WDT_STATUS	TYPE_WDT_DISABLE	//如果配置为enable，请在bsp_config.c中设置wdt溢出时间
	#define D_MCU_ENDIAN	TYPE_MCU_BIGENDIAN
	#define D_CODE_ENCRYPTION_TYPE 	TYPE_ENCRYPTION_ENABLE	//是否代码加密


	#define D_MCU_NAME "STC8H3K64S4"
	//存储器特殊参数地址配置
	#define D_MCU_SPEC_PARAM_CHIPID	0xFDF9
	//...其他参数
	#if ((TYPE_MCU & TYPE_MCU_VENDOR_MSK) == TYPE_MCU_VENDOR_STC)

		#include "../cpu/STC_stc8h3k.h"
		#include "../cpu/STC_only.h"
		#include "../cpu/c51_macro.h"
	#endif
	
	//Step3:  >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>IRQ Config
#if ((TYPE_MCU & TYPE_MCU_VENDOR_MSK) == TYPE_MCU_VENDOR_STC)


#define D_SERVE_INT0	interrupt 0
#define D_SERVE_TIMER0	interrupt 1
#define D_SERVE_INT1   	interrupt 2
#define D_SERVE_TIMER1	interrupt 3
///#define D_SERVE_UART	interrupt 4
#define D_SERVE_ADC		interrupt 5
#define D_SERVE_LVD		interrupt 6
#define D_SERVE_PCA		interrupt 7
#define D_SERVE_UART2	interrupt 8
#define D_SERVE_SPI		interrupt 9
#define D_SERVE_INT2	interrupt 10
#define D_SERVE_INT3	interrupt 11
#define D_SERVE_TIMER2	interrupt 12
#define D_SERVE_INT4	interrupt 16
#define D_SERVE_UART3   interrupt 17
#define D_SERVE_UART4	interrupt 18
#define D_SERVE_TIMER3  interrupt 19
#define D_SERVE_TIMER4  interrupt 20
#define D_SERVE_CMP  	interrupt 21
#define D_SERVE_PWM   	interrupt 22
#define D_SERVE_PWMFD   interrupt 23
#define D_SERVE_I2C   	interrupt 24
#endif



	
#define D_ISR_int0		0		///int0 下降沿触发  = 0 上下沿均可触发
#define D_ISR_timer0	1
#define D_ISR_int1		2		///int1 下降沿触发  = 0 上下沿均可触发
#define D_ISR_timer1 	3
#define D_ISR_int2		10		/////只有下降沿
#define D_ISR_int3		11		/////只有下降沿
#define D_SERVE_UART   interrupt	4
#define D_SERVE_UART1   interrupt	8
#define D_ISR_int4		16		/////只有下降沿

	
	//串口配置
	#define D_uart0_BRT 	BRT_115200
	#define D_uart0_SBIT 	SBIT_1
	#define D_PIN_UART0		PIN_UART0_Rxd_30_Txd_31

	#define D_uart2_BRT 	BRT_115200
	#define D_uart2_SBIT 	SBIT_1
	#define D_PIN_UART2		PIN_UART2_Rxd_10_Txd_11 //wifi模块

	#define D_uart3_BRT 	BRT_115200
	#define D_uart3_SBIT 	SBIT_1
	#define D_PIN_UART3 	PIN_UART3_Rxd_00_Txd_01 //声音模块
	
	#define D_uart4_BRT 	BRT_115200
	
	//485配置
	#define D_UART0_485_TYPE TYPE_485_NONE	//UART0启用485
	#define D_UART0_485_SLAVER_ID_BROADCAST 0xFF	//485从机总是响应0xFF消息
	#define D_UART0_485_SLAVER_ID 0x01			//板卡作为485从机 slaverId
	// #define D_UART0_485_TX()		P32 = 1;
	// #define D_UART0_485_RX()		P32 = 0;
	#define D_UART2_485_TYPE TYPE_485_NONE	//UART2不启用485
	#define D_UART3_485_TYPE TYPE_485_NONE	//UART2不启用485
	#define D_UART4_485_TYPE TYPE_485_NONE	//UART2不启用485
	
	//MODBUS协议配置
	#define D_MODBUS_ENABLE	//MODBS启用开关，如果不使用modbus，可以注释掉本行
	#define D_MODBUS_SPLIT_ENTRY 	L1_modbus_split		//modbus切割函数，在tpc_modbus.c中实现，依据实际情况修改
	#define D_MODBUS_REG_MAX_NUM 	32 	//每次最多读取/写入的寄存器数量，此处的数量要注意和 D_tp_handle_x_len 对应
	
	//外设定义	
  	#define LED1	P27		//D4
	#define LED2	P26		//D4
	#define LED3	P02		//D4
	#define LED4	P55		//D4

	//笔头
	#define SCK    P34
	#define SDIO   P50

	// 3V3输出控制（WIFI，笔头供电）
	#define L0_PW_3V3_INIT()	D_HighI_P5(BITN3)
	#define L0_PW_3V3_ON()		D_P53_OFF() 
	#define L0_PW_3V3_OFF()		D_P53_ON()

	
	//按键
	#define key1	P32   //音量增大
	#define key2	P33   //音量减小	
	#define key3	P40   //开关机
	//EEP存储地址定义
	#define D_EEP_SECTOR_SIZE 0x200	//每个扇区0x200==512bytes
	#define D_EEP_SECTOR_BLOCK_SIZE 0x40	//扇区中每个数据块0x40==64bytes，可选值[32,64,128]等
	#define D_EEP_SECTOR_BLOCK_NUM (D_EEP_SECTOR_SIZE / D_EEP_PARAM_BLOCK_SIZE) //每个扇区数据块的数量
	#define D_EEP_BLOCK_FILTER0 0xAA	//扇区中每个数据块的Filter字段值
	#define D_EEP_BLOCK_FILTER1 0x55	
	//EEP User Defined 参数区存储配置	
	#define D_EEP_PARAM_IN_SECTOR 1		//eeprom参数区扇区地址，从0开始
	#define D_EEP_PARAM_IN_BLOCK 0		//eeprom参数区数据块地址，从0开始
	//#define D_EEP_PARAM_BLOCK_SIZE 	(D_EEP_SECTOR_BLOCK_SIZE)	//参数区每个块大小，必须：D_EEP_PARAM_BLOCK_SIZE<=D_EEP_SECTOR_BLOCK_SIZE!!!，因为eeprom.h中是按照D_EEP_SECTOR_BLOCK_SIZE分配的buf
	//#define D_EEP_PARAM_BLOCK_NUM 	(D_EEP_SECTOR_SIZE / D_EEP_PARAM_BLOCK_SIZE) //每个扇区数据块的数量
	//EEP 加密区存储配置
	#if(D_CODE_ENCRYPTION_TYPE == TYPE_ENCRYPTION_ENABLE)
	#define D_EEP_ENC_IN_SECTOR 0 		//eeprom加密区扇区地址，从0开始
	#define D_EEP_ENC_IN_BLOCK 0 		//eeprom加密区数据块地址，从0开始
	//#define D_EEP_ENC_BLOCK_SIZE 	0x20	//ENC_BLOCK_SIZE必须与加密程序中的ENC_BLOCK_SIZE匹配，此处不建议修改，如需修改，请同时修改加密程序
	#endif

//STEP 2 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<TYPE_UASER_BOARD CONFIG End





//STEP 3 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<IRQ Config End



/**************************************模拟i2c_cw63xx********************************************/

#define L0_IIC_SIM_INIT()		  BITN_0(P3M1,5);BITN_0(P3M0,5);BITN_0(P5M1,1);BITN_0(P5M0,1);//io
#define L0_IIC_SIM_close()	  BITN_1(P3M1,5);BITN_0(P3M0,5);BITN_1(P5M1,1);BITN_0(P5M0,1);//
							
#if 10
#define L0_SDA_ON()		D_P51_ON() 
#define L0_SDA_OFF()	D_P51_OFF() 
#define L0_SDA_AT()		D_P51_AT() 
#define L0_SCL_ON()		D_P35_ON() 
#define L0_SCL_OFF()	D_P35_OFF() 
#define L0_SCL_AT()	  	D_P35_AT() 	
#define L0_SDA_OUT()	D_P51_AT() //////FIXME
#define L0_SDA_IN()		D_P51_ON() //////FIXME

#else
#define L0_SDA_ON()		//D_P34_ON() 
#define L0_SDA_OFF()	//D_P34_OFF() 
#define L0_SDA_AT()		//D_P34_AT() 
#define L0_SCL_ON()		//D_P35_ON() 
#define L0_SCL_OFF()	//D_P35_OFF() 

#endif
/**************************************模拟i2c_msa300********************************************/

#define L0_SDA2_INIT()		D_stdIO_P5(BITN1)///D_HighR_P5(BITN1)
#define L0_SDA2_CLOSE()		D_HighR_P5(BITN1)

#define L0_SDA2_ON()		D_P51_ON() 
#define L0_SDA2_OFF()	  	D_P51_OFF() 
#define L0_SDA2_AT()		D_P51_AT() 
#define L0_SDA2_OUT()	  	D_stdIO_P5(BITN1) //////FIXME
#define L0_SDA2_IN()		D_HighR_P5(BITN1) //////FIXME

#define L0_SCL2_INIT()		D_stdIO_P3(BITN5)
#define L0_SCL2_CLOSE()		D_HighR_P3(BITN5)

#define L0_SCL2_ON()		D_P35_ON() 
#define L0_SCL2_OFF()	  	D_P35_OFF() 
#define L0_SCL2_AT()	  	D_P35_AT() 

#define L0_IIC2_SIM_INIT();		L0_SDA2_INIT();L0_SCL2_INIT();///
#define L0_IIC2_SIM_close();	L0_SDA2_CLOSE();L0_SCL2_CLOSE();////BITN_1(P2M1,5);BITN_0(P2M0,5);BITN_1(P2M1,4);BITN_0(P2M0,4);//





//STEP 4 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Cdelay CONFIG 
#if(MainFre_5M == D_sys_MainFre)
#define D_Cdelay_200us		20
#define D_Cdelay_1us		1		////while p21翻转时测定  500k 2us 一个指令
#elif(MainFre_22M == D_sys_MainFre) 
#define D_Cdelay_200us		20
#define D_Cdelay_1us		1		////while p21翻转时测定  500k 2us 一个指令
#define D_Cdelay_1us		1		////while p21翻转时测定  500k 2us 一个指令
#define L0_delay_1us()	Lc_delay_nop(0) 	// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
#define L0_delay_10us() Lc_delay_nop(4) 	// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
#define L0_delay_40us() Lc_delay_nop(18)	// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
#elif(MainFre_27M == D_sys_MainFre)
#define D_Cdelay_200us		20
#define D_Cdelay_1us		1		////while p21翻转时测定  500k 2us 一个指令
#else		///MainFre_11M	
#define D_Cdelay_200us		20
#define D_Cdelay_1us		1		////while p21翻转时测定  500k 2us 一个指令
#define L0_delay_1us()	Lc_delay_nop(0) 	// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
#define L0_delay_10us() Lc_delay_nop(4) 	// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
#define L0_delay_40us() Lc_delay_nop(18)	// 5个nop()  100ns  50个nop() 1us   (20)=10us  (2)1.5us
		//xx
#endif//D_sys_MainFre)
//STEP 4 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Cdelay CONFIG End




/*************************************************************
1，
串口1选择定时器2为波特率发生器
			AUXR &= 0xFB;		//定时器2时钟为Fosc/12,即12T,
2， timer0 为task使用
L1_tick_tick
3，

***************************default*************************************/
#if 0
#define D_IO_LED1_OFF()   	D_P27_ON()
#define D_IO_LED1_ON() 		D_P27_OFF()	
#define D_IO_LED1_REV()		D_P27_REV()	

#define D_IO_LED1_H()   	D_P27_ON()
#define D_IO_LED1_L() 		D_P27_OFF()	
#define D_IO_LED2_H()   	D_P26_ON()
#define D_IO_LED2_L()		D_P26_OFF()	




#define D_IO_LEDkey2_OFF()		D_P55_OFF()
#endif

//STEP 5 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Uart CONFIG
// #define SERIAL_MAX_NUM 3     ???
////fixme:和cpu的程序容量息息相关
#define D_UART_send_buf_max		32  /// 9600bps = 10000bps = 1000 Bps = 1Byte/ms
							    /// 19200bps = 20000bps = 2000Bps = 2Byte/ms  = 1Byte/0.5ms
								///  128Bytes = 128*0.5ms = 64ms
#define D_UART_send_buf2_max		8	//此处改动会影响L0_uartN_ulhex函数
//STEP 5 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Uart CONFIG End






//STEP 6 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Transmission Protocol Config 
#define D_TPC_CCMODBUS_Filter0 	0xFF
#define D_TPC_CCMODBUS_Filter1 	0xFE
#define D_TPC_DEBUG_FX_fi	0xF0
#define D_TPC_DEBUG_FX_MASK	0x0F
#define D_TPC_HANDLER_X_LEN 128

//STEP 6 <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<Transmission Protocol Config End

#elif(TYPE_UASER_BOARD == TYPE_BOARD_SMMM_MB_VH032_0E)
	xxx
#endif


extern void L0_board_config(void);


#endif//_BSP_CONFIG_H
/*********************************end file*********************************************/